Shop News

M390 Steel: Reading the Spec Sheet Behind a Premium Blade

M390 steel is a powder metallurgy stainless steel made by Böhler, built for very high wear resistance. In plain knife terms, that means an edge that keeps cutting for a long time between sharpenings, with good rust resistance and a blade that takes a fine, polished finish. The tradeoffs are a slower sharpening session when the edge does go dull, and toughness that is good rather than exceptional.

You will find it on upgraded versions of everyday carry favorites and on a lot of premium automatics and fixed blades. To understand why it behaves the way it does, it helps to look at what is actually in it.

What Is in M390 Steel

Böhler publishes the average chemical composition of M390 on its M390 Microclean datasheet. Here it is, with what each element does in a knife blade:

Element Amount (wt. %) What it does in a knife

 

Carbon (C) 1.9 Allows high hardness and forms hard carbides that resist wear
Chromium (Cr) 20 Provides stainless rust resistance; also forms chromium carbides
Vanadium (V) 4 Forms very hard vanadium carbides, a big reason for long edge life
Molybdenum (Mo) 1 Helps corrosion resistance and hardenability
Tungsten (W) 0.6 Adds to wear resistance
Silicon (Si) 0.7 Helps during steelmaking and adds some strength
Manganese (Mn) 0.3 Helps hardening

Two numbers explain most of M390’s personality. The carbon content is very high for a stainless steel, and so is the chromium. Together with 4 percent vanadium, they create a large volume of carbides. Carbides are tiny, extremely hard particles in the steel, and they are what keep scraping away at cardboard, rope and plastic without the edge rounding off quickly.

Why Powder Metallurgy Matters

A steel with this much carbon and chromium would be hard to use for knives if it were made the traditional way. In conventional steelmaking, carbides can grow large and clump as a big ingot cools, which makes a blade more brittle and harder to grind.

Böhler makes M390 with powder metallurgy and sells it under its Microclean name. The molten steel is turned into a fine powder, and that powder is then consolidated back into solid steel. The result is small carbides spread evenly through the blade instead of large clumps. Benchmade’s own blade steel guide sums M390 up as a powder metallurgy “super-steel” that “takes a fine edge.”

For you, that means an edge that can be ground thin and keen, holds a fine finish, and is far less prone to chipping than the composition alone would suggest.

How Böhler Rates It

Böhler’s own ratings for M390 are worth reading closely, because they are honest about the balance:

  • Wear resistance: very high
  • Polishability: very high
  • Corrosion resistance: good
  • Toughness and ductility: good

Translated into everyday use: excellent edge retention, a blade that takes a mirror or satin finish beautifully, solid rust resistance for a stainless steel, and enough toughness for normal cutting, but not the steel you would choose for chopping or prying.

M390 Steel Hardness Depends on the Knife Maker

Böhler’s datasheet gives heat treatment ranges rather than a single knife hardness, because the final number depends on how each knife company hardens and tempers its blades. Lower tempering favors corrosion resistance, while higher tempering with multiple cycles favors wear resistance.

Benchmade, for example, lists the M390 version of its aluminum Bugout at 58 to 61 HRC, and other makers set their own targets. That range is hard enough to hold an edge for a long time while leaving some give in the steel.

Where You Will Find M390

M390 tends to appear as a step-up option or on premium models:

The Bugout upgrade is a good illustration of what M390 is for. The standard Bugout uses CPM-S30V. Moving to M390 keeps the same thin, slicey blade but extends how long it stays sharp, which suits a knife that does a lot of light daily cutting.

M390 is not the only premium option on the shelf, and our head-to-head of MagnaCut, S30V and D2 edge steels shows where three other popular choices land.

Browse M390 folders and more: Sharp Things OKC stocks knives in a wide range of premium steels at 6610 N May Ave, open 9AM to 9PM every day, and you can shop our folding knives online.

Sharpening M390 Without Frustration

The same carbides that make M390 hold an edge make it slower to sharpen. Soft natural stones and basic pull-through sharpeners struggle to cut those hard carbides cleanly. A few habits help:

  1. Use abrasives that are harder than the carbides. Diamond plates and good ceramic or synthetic stones work far better than soft stones.
  2. Do not let it get very dull. Touching up a slightly dull edge takes a few minutes. Reprofiling a badly worn one takes much longer.
  3. Strop lightly to finish. A leather strop with compound cleans up the burr and leaves a crisp edge.
  4. Keep the angle consistent. A guided system makes this easier if you are new to freehand sharpening.

If you are still building your technique, our freehand and guided sharpening walkthrough covers stones, grits and holding a steady angle.

Living With an M390 Blade

Böhler calls its corrosion resistance good, not perfect. In daily carry, M390 is very hard to rust, but it can spot if left wet with salt water, blood or acidic food. Wipe the blade after use, rinse it with fresh water after saltwater trips, and you will rarely see a mark.

Do not use an M390 blade as a pry bar or screwdriver. Its toughness is fine for cutting, but twisting a thin, hard edge sideways is the fastest way to chip it.

Who Should Choose M390

M390 is a strong pick if you:

  • Cut a lot of abrasive materials like cardboard, rope, zip ties and plastic packaging
  • Want to sharpen less often
  • Like a polished or satin blade that stays looking clean
  • Carry a slim EDC folder and want the most edge life from it

It is less suited to people who want the easiest possible steel to sharpen in the field, or who need maximum toughness for chopping and batoning.

M390 Steel Rewards Slicers, Not Pry Bars

M390 is a high-carbon, high-chromium powder steel from Böhler with very high wear resistance and good corrosion resistance. Expect long edge life, a blade that polishes beautifully, and slower sharpening when the time comes. If your knife spends its life slicing rather than prying, it is one of the most satisfying premium steels you can carry.

Feel the difference an upgraded steel makes: stop by Sharp Things OKC on N May Ave in Oklahoma City and look at how a stonewashed or satin M390 blade compares with coated and tumbled finishes on other premium steels. If a compact fixed blade suits your carry better than a folder, the Microtech SOCOM Alpha Mini in M390 is a strong place to start at SharpThings.com.

Frequently Asked Questions

Who makes M390 steel?

M390 is made by Böhler, part of the voestalpine group, and sold as M390 Microclean. Böhler lists custom hand knives and industrial knives among its uses.

Is M390 a stainless steel?

Yes. With around 20 percent chromium, it is a stainless steel, and Böhler rates its corrosion resistance as good. It still benefits from being wiped dry, especially after contact with salt or acidic foods.

Is M390 better than S30V?

They suit different priorities. M390 generally offers more wear resistance and longer edge life, while CPM-S30V is easier to sharpen and is a well-rounded steel designed for pocket knife blades. Many owners pick M390 when they want to sharpen less often.

Can M390 take a mirror polish?

Yes. Böhler rates its polishability as very high, which is one reason M390 blades often come in clean satin or polished finishes.

Does M390 chip easily?

Not in normal cutting. Its toughness is rated good, and the fine powder metallurgy structure helps. Chipping usually comes from twisting the blade, prying, or cutting into hard objects like staples or bone.

Leave a Reply